|
|
We offer superior quality rubber sheets in variable thicknesses and dimensions. These rubber sheets are used as floor coverings around the electrical panels and between the flanges & joints subjected to air pressure & water. These sheets are manufactured using the blend of high quality natural and synthetic rubber. Tested on various parameters of friction and durability, the range is also customized as per the requirements of client. |
Rubber Mats For Electrical Purposes
APPLICATION Rubber mats are used as floor covering around electrical panels as a safeguard to the life and limb of the workmen due to possible leakage of current and short-circuit. Rubber mats are used in power generation plants, sub-stations, workshops etc. EXCEPTIONAL FEATURESJYOTI are the only manfacturers in the whole of North India to have been granted Certification Mark licence for Rubber Mats as per IS-5424. | CONSTRUCTION | | Composition | Manufactured out of rubber compound of high quality Natural Rubber. | | Surface | The rubber mats have chequered, anti-skid fluted design or plain at bottom as per the requirement of the purchaser. | | Thickness Range | 8.5 mm to 25 mm for chequered or fluted 6.5 mm to 25 mm for plain. | | Length x Width | 2.0 mtr x 1.0 mtr. | | | 1.8 mtr x 0.9 mtr. | | Technical Particulars | Tensile strength 50 kgf/cm2 | | | Elongation at break 250% | | Voltage Test | The rubber mats are tested to pass the voltage test at 15000 volts for one minute without any puncture or warming effect. | | Breakdown Strength | Shall not fail at less than 40000 volts as per the procedure outlined in IS : 2584/83. | |
|
|
|
|
|
|
Rubber Insertion Jointing For Air and Water Pressure
Application Used between flanges and similar joints subjected to water & air pressure. Construction
| | Rubber Composition | Manufactured out of Rubber compound of high quality Natural or Synthetic rubber or a blend thereof. | | Reinforcement | The reinforcement fabric used shall have a minimum breaking load of 120 N/cm width for both warp and weft direction. | | Colour & Finish | Unless otherwise specified colour shall be off-white having cloth marked finish on both surfaces. | | Size | Thickness of Sheet, Permissible Tolerances, number of fabric plies, width and length shall be as given below :- | | Thickness mm | Tolerance mm | No. of plies | Width (mtr.) | Length (mtr.) | | 1.5 | + 0.2 | 1 | 1.0 | 10.0 | | 3.0 | + 0.3 | 2 | 1.0 | 10.0 | | 5.0 | + 0.5 | 2 | 1.0 | 10.0 | | 6.0 | + 0.6 | 3 | 1.0 | 10.0 | | 8.0 & above | + 0.7 | 4 | 1.0 | as per agreement | Technical specifications
| Type | Tensile Strength Kgf/cm2 | Elongation at break (percentage) | Hardness (IRHD) | Compression set (percentage) | | | Grade 1 | Grade 2 | Grade 1 | Grade 2 | | | | A | 85 | 60 | 400 | 350 | 50-65 | 35(Max) | | B | 85 | 60 | 300 | 250 | 66-80 | 35(Max) | |
|
|
|
|
Nitrile Rubber Sheets
As per BS 2751 are highly resistant to petroleum products and suitable for use at high temperature upto +240°F and also where food grade sheets are required. Calendered or Press moulded finish. Thickness:
0.5 to 100.0 mm as per requirement of the customer. Size:
1 meter x 2 meters in mould finish or long length from 0.5 mm to 6.0 mm thickness in calendered finish. |
|
Neoprene Sheets
Rubber sheets as per BS : 2752 Besides being resistant to petroleum products like Nitrile rubber sheets, Neoprene sheets are also resistant to temperature ranging from (-) 40°F to (+)300°F, acids, alkalies, open flame and also where food grade non-toxic sheets are required. Thickness: 0.5 to 100.0 mm as per requirement of the customer. Size: 1 meter x 2 meters in mould finish or long length from 0.5 mm to 6.0 mm thickness in calendered finish. |
|
|
|
|
|
|
EPDM Rubber sheets
Recommended where sheets for use under higher temperature ranging from (-) 40°F to (+)400°F are required and have resistance to a wide range of chemical intermediates in chemical and pharmaceutical industries, fertilizer plants, steel mills etc. Thickness: 0.5 to 100.0 mm as per requirement of the customer. Size: 1 meter x 2 meters in mould finish or long length from 0.5 mm to 6.0 mm thickness in calendered finish. |
|
Silicon Rubber Sheets And Hoses
Recommended for use at extra high temperature ranging from (-) 40°F to (+) 900°F Thickness and Size: Sheets offered in moulded finish in thickness of 1.5 mm to 12.5 mm in 1 meter width and length upto 3 meters. |
|
|
|
|
|
|
